Over 500 CompTIA Network+ N10-007 Exam Questions and Answers

The latest CompTIA Network+ N10-007 certification actual real practice exam question and answer (Q&A) dumps are available free, which are helpful for you to pass the CompTIA Network+ N10-007 exam and earn CompTIA Network+ certification.

Keyword: Free Exam Dumps, Exam Questions, Exam Dumps, Braindumps, Real Questions, Practice Test, Practice Exam, Free Test, Free Questions, Real Exam Questions and Answers, VCE Dumps, ETE Dumps, PDF Dumps, and Study Guide.

Question 1: A technician has racked a new access switch and has run multimode fiber to a new location. After installing an extended-range 10Gb SFP in the core switch, the technician installed a 10Gb SFP in the access switch and connected the port to the new extension with a fiber jumper. However, the link does not display, and the technician cannot see light emitting from the core switch. Which of the following solutions is MOST likely to resolve the problem?

A. Swap the fiber pairs in one of the SFPs
B. Replace the jumpers with single-mode fiber
C. Set the correct MTU on the new interface
D. Install an optic that matches the fiber type

Question 2: A firewall administrator is implementing a rule that directs HTTP traffic to an internal server listening on a non-standard socket. Which of the following types of rules is the administrator implementing?

A. NAT
B. PAT
C. STP
D. SNAT
E. ARP

Question 3: A technician is installing a new wireless badging system on a hospital network. The requirements of the badging system are for it to have its own SSID and low power levels. The badging system has to cover 99.9% of the hospital. Which of the following is the BEST action to take to meet the system requirements?

A. Install additional WAPs
B. Install external antennas
C. Move the WAPs closer to the more populated area
D. Change the antenna types

Question 4: A technician attempts to replace a switch with a new one of similar model from the same vendor. When the technician moves the fiber and SFP plug, the switch does not completely boot up. Considering that the config files are the same, which of the following is the MOST likely cause of the failure?

A. Damaged fiber
B. Corrupted operating system
C. VLAN mismatch
D. Bad port

Question 5: A company has completed construction of a new datacenter, and the IT staff is now planning to relocate all server and network equipment from the old site to the new site. Which of the following should the IT staff reference to determine the location of the equipment being moved?

A. Rack diagrams
B. Network topology
C. Standard operating procedures
D. Wiring documentation

Question 6: A technician wants to prevent an unauthorized host from connecting to the network via Ethernet. Which of the following is a Layer 2 access control the technician should implement?

A. Access control lists
B. Captive portal
C. WPA2
D. Port security

Question 7: A network technician is deploying mobile phones for a company’s sales staff. Salespeople frequently travel nationally and internationally to meet with clients, and often have to roam or switch cellular providers. Which of the following standards is the BEST option to fit the requirements?

A. GSM
B. TDM
C. CDMA
D. PSTN
E. MIMO

Question 8: A network administrator has been given a network of 172.16.85.0/21 and wants to know the usable range of IP addresses on that subnet. Which of the following indicates the correct IP address range?

A. 172.16.80.0-172.16.85.254
B. 172.16.80.0-172.16.88.255
C. 172.16.80.1-172.16.87.254
D. 172.16.80.1-172.16.85.255

Question 9: A network technician is troubleshooting wireless network issues in a crowded office complex and suspects there is interference from nearby wireless networks. Which of the following should the technician perform to discover possible interference?

A. Site survey
B. Vulnerability scanning
C. Wardriving
D. Checking logical diagram
E. Bandwidth test

Question 10: A network technician has discovered a rogue access point placed under an empty cubicle desk. Which of the following should the technician perform to ensure another cannot be placed on the network?

A. Disable unused ports on switches
B. Enable DHCP guard to detect rogue servers
C. Configure WPA2 on all access points
D. Use TACACS+ authentication