The latest Cisco CCNP and CCIE Enterprise Core: Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR) 350-401 certification actual real practice exam question and answer (Q&A) dumps are available free, which are helpful for you to pass the Cisco CCNP and CCIE Enterprise Core: Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR) 350-401 exam and earn Cisco CCNP and CCIE Enterprise Core: Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR) 350-401 certification.
Exam Question 81
Refer to the exhibit. R1 is able to ping the R3 fa0/1 interface. Why do the extended pings fail?
A. The maximum packet size accepted by the command is 1476 bytes.
B. The DF bit has been set.
C. R3 is missing a return route to 10.99.69.0/30.
D. R2 and R3 do not have an OSPF adjacency.
Correct Answer:
B. The DF bit has been set.
Exam Question 82
Refer to the exhibit. Which command allows hosts that are connected to FastEthernet0/2 to access the Internet?
A. ip nat inside source list 10 interface FastEthernet0/2 overload
B. ip nat inside source list 10 interface FastEthernet0/1 overload
C. ip nat outside source static 209.165.200.225 10.10.10.0 overload
D. ip nat outside source list 10 interface FastEthernet0/2 overload
Correct Answer:
B. ip nat inside source list 10 interface FastEthernet0/1 overload
Exam Question 83
Refer to the exhibit. What are two effects of this configuration? (Choose two.)
A. If R1 goes down, R2 becomes active but reverts to standby when R1 comes back online.
B. If R2 goes down, R1 becomes active but reverts to standby when R2 comes back online.
C. R1 becomes the active router.
D. R1 becomes the standby router.
E. If R1 goes down, R2 becomes active and remains the active device when R1 comes back online.
Correct Answer:
C. R1 becomes the active router.
E. If R1 goes down, R2 becomes active and remains the active device when R1 comes back online.
Exam Question 84
Refer to the exhibit.
Which two commands ensure that DSW1 becomes root bridge for VLAN 10? (Choose two.)
A. DSW1(config)#spanning-tree vlan 10 priority 4096
B. DSW1(config)#spanning-tree vlan 10 priority root
C. DSW2(config)#spanning-tree vlan 10 priority 61440
D. DSW1(config)#spanning-tree vlan 10 port-priority 0
E. DSW2(config)#spanning-tree vlan 20 priority 0
Correct Answer:
A. DSW1(config)#spanning-tree vlan 10 priority 4096
B. DSW1(config)#spanning-tree vlan 10 priority root
Exam Question 85
What mechanism does PIM use to forward multicast traffic?
A. PIM sparse mode uses a pull model to deliver multicast traffic.
B. PIM dense mode uses a pull model to deliver multicast traffic.
C. PIM sparse mode uses receivers to register with the RP.
D. PIM sparse mode uses a flood and prune model to deliver multicast traffic.
Correct Answer:
A. PIM sparse mode uses a pull model to deliver multicast traffic.
Exam Question 86
Refer to the exhibit.
The traceroute fails from R1 to R3. What is the cause of the failure?
A. An ACL applied inbound on loopback0 of R2 is dropping the traffic.
B. The loopback on R3 is in a shutdown state.
C. Redistribution of connected routes into OSPF is not configured.
D. An ACL applied inbound on fa0/1 of R3 is dropping the traffic.
Correct Answer:
D. An ACL applied inbound on fa0/1 of R3 is dropping the traffic.
Exam Question 87
Refer to the exhibit.
An engineer must establish eBGP peering between router R3 and router R4. Both routers should use their loopback interfaces as the BGP router ID.
Which configuration set accomplishes this task?
A. R3(config)#router bgp 200
R3(config-router)#neighbor 10.4.4.4 remote-as 100
R3(config-router)# neighbor 10.4.4.4 update-source Loopback0
R4(config)#router bgp 100
R4(config-router)#neighbor 10.3.3.3 remote-as 200
R4(config-router)#network 10.3.3.3 update-source Loopback0
B. R3(config)#router bgp 200
R3(config-router)#neighbor 10.24.24.4 remote-as 100
R3(config-router)#neighbor 10.24.24.4 update-source Loopback0
R4(config)#router bgp 100
R4(config-router)#neighbor 10.24.24.3 remote-as 200
R4(config-router)#neighbor 10.24.24.3 update-source Loopback0
C. R3(config)#router bgp 200
R3(config-router)#neighbor 10.4.4.4 remote-as 100
R3(config-router)#bgp router-id 10.3.3.3
R4(config)#router bgp 100
R4(config-router)#neighbor 10.3.3.3 remote-as 200
R4(config-router)#bgp router-id 10.4.4.4
D. R3(config)#router bgp 200
R3(config-router)#neighbor 10.24.24.4 remote-as 100
R3(config-router)#bgp router-id 10.3.3.3
R4(config)#router bgp 100
R4(config-router)#neighbor 10.24.24.3 remote-as 200
R4(config-router)#bgp router-id 10.4.4.4
Correct Answer:
A. R3(config)#router bgp 200
R3(config-router)#neighbor 10.4.4.4 remote-as 100
R3(config-router)# neighbor 10.4.4.4 update-source Loopback0
R4(config)#router bgp 100
R4(config-router)#neighbor 10.3.3.3 remote-as 200
R4(config-router)#network 10.3.3.3 update-source Loopback0
Exam Question 88
Which two security features are available when implementing NTP? (Choose two.)
A. encrypted authentication mechanism
B. symmetric server passwords
C. clock offset authentication
D. broadcast association mode
E. access list-based restriction scheme
Correct Answer:
A. encrypted authentication mechanism
E. access list-based restriction scheme
Answer Description:
Exam Question 89
Refer to the exhibit.
After an engineer configures an EtherChannel between switch SW1 and switch SW2, this error message is logged on switch SW2:
SW2#
09:45:32: %PM-4-ERR_DISABLE: channel-misconfig error detected on Gi0/0, putting Gi0/0 in err-disable
state
09:45:32: %PM-4-ERR_DISABLE: channel-misconfig error detected on Gi0/1, putting Gi0/1 in err-disable
state
Based on the output from switch SW1 and the log message received on switch SW2, what action should the engineer take to resolve this issue?
A. Configure the same protocol on the EtherChannel on switch SW1 and SW2.
B. Define the correct port members on the EtherChannel on switch SW1.
C. Correct the configuration error on Interface Gi0/0 on switch SW1.
D. Correct the configuration error on Interface Gi0/1 on switch SW1.
Correct Answer:
A. Configure the same protocol on the EtherChannel on switch SW1 and SW2.
Exam Question 90
Refer to the exhibit. Communication between London and New York is down. Which command set must be applied to resolve this issue?
A. NewYork(config)#int f0/1
NewYork(config)#switchport nonegotiate
NewYork(config)#end
NewYork#
B. NewYork(config)#int f0/1
NewYork(config)#switchport mode trunk
NewYork(config)#end
NewYork#
C. NewYork(config)#int f0/1
NewYork(config)#switchport trunk encap dot1q
NewYork(config)#end
NewYork#
D. NewYork(config)#int f0/1
NewYork(config)#switchport mode dynamic desirable
NewYork(config)#end
NewYork#
Correct Answer:
B. NewYork(config)#int f0/1
NewYork(config)#switchport mode trunk
NewYork(config)#end
NewYork#