The latest Cisco CCNP and CCIE Enterprise Core: Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR) 350-401 certification actual real practice exam question and answer (Q&A) dumps are available free, which are helpful for you to pass the Cisco CCNP and CCIE Enterprise Core: Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR) 350-401 exam and earn Cisco CCNP and CCIE Enterprise Core: Implementing and Operating Cisco Enterprise Network Core Technologies (ENCOR) 350-401 certification.
Exam Question 41
Which antenna type should be used for a site-to-site wireless connection?
A. patch
B. dipole
C. omnidirectional
D. Yagi
Correct Answer:
D. Yagi
Exam Question 42
What does the LAP send when multiple WLCs respond to the CISCO-CAPWAPCONTROLLER.localdomain hostname during the CAPWAP discovery and join process?
A. unicast discovery request to the first WLC that resolves the domain name
B. broadcast discovery request
C. join request to all the WLCs
D. unicast discovery request to each WLC
Correct Answer:
A. unicast discovery request to the first WLC that resolves the domain name
Exam Question 43
Which DNS lookup does an access point perform when attempting CAPWAP discovery?
A. CISCO-CONTROLLER.local
B. CAPWAP-CONTROLLER.local
C. CISCO-CAPWAP-CONTROLLER.local
D. CISCO-DNA-CONTROLLER.local
Correct Answer:
C. CISCO-CAPWAP-CONTROLLER.local
Exam Question 44
Refer to the exhibit.
What are two effects of this configuration? (Choose two.)
A. It establishes a one-to-one NAT translation.
B. The 209.165.201.0/27 subnet is assigned as the outside local address range.
C. The 10.1.1.0/27 subnet is assigned as the inside local addresses.
D. Inside source addresses are translated to the 209.165.201.0/27 subnet.
E. The 10.1.1.0/27 subnet is assigned as the inside global address range.
Correct Answer:
C. The 10.1.1.0/27 subnet is assigned as the inside local addresses.
D. Inside source addresses are translated to the 209.165.201.0/27 subnet.
Exam Question 45
An engineer configures a WLAN with fast transition enabled. Some legacy clients fail to connect to this WLAN.
Which feature allows the legacy clients to connect while still allowing other clients to use fast transition based on their OUIs?
A. over the DS
B. 802.11k
C. adaptive R
D. 802.11v
Correct Answer:
C. adaptive R
Exam Question 46
Which two pieces of information are necessary to compute SNR? (Choose two.)
A. transmit power
B. noise floor
C. EIRP
D. RSSI
E. antenna gain
Correct Answer:
A. transmit power
B. noise floor
Exam Question 47
Which OSPF network types are compatible and allow communication through the two peering devices?
A. point-to-multipoint to nonbroadcast
B. broadcast to nonbroadcast
C. point-to-multipoint to broadcast
D. broadcast to point-to-point
Correct Answer:
B. broadcast to nonbroadcast
Exam Question 48
Which statement about multicast RPs is true?
A. RPs are required only when using protocol independent multicast dense mode.
B. RPs are required for protocol independent multicast sparse mode and dense mode.
C. By default, the RP is needed periodically to maintain sessions with sources and receivers.
D. By default, the RP is needed only to start new sessions with sources and receivers.
Correct Answer:
D. By default, the RP is needed only to start new sessions with sources and receivers.
Exam Question 49
To increase total throughput and redundancy on the links between the wireless controller and switch, the customer enabled LAG on the wireless controller.
Which EtherChannel mode must be configured on the switch to allow the WLC to connect?
A. Active
B. Passive
C. On
D. Auto
Correct Answer:
C. On
Exam Question 50
Refer to the exhibit.
Link1 is a copper connection and Link2 is a fiber connection. The fiber port must be the primary port for all forwarding. The output of the show spanning-tree command on SW2 shows that the fiber port is blocked by spanning tree. An engineer enters the spanning-tree port-priority 32 command on G0/1 on SW2, but the port remains blocked.
Which command should be entered on the ports that are connected to Link2 to resolve the issue?
A. Enter spanning-tree port-priority 4 on SW2.
B. Enter spanning-tree port-priority 32 on SW1.
C. Enter spanning-tree port-priority 224 on SW1.
D. Enter spanning-tree port-priority 64 on SW2.
Correct Answer:
B. Enter spanning-tree port-priority 32 on SW1.