The latest CompTIA Network+ N10-007 certification actual real practice exam question and answer (Q&A) dumps are available free, which are helpful for you to pass the CompTIA Network+ N10-007 exam and earn CompTIA Network+ certification.
Exam Question 411
A penetration tester has been tasked with reconnaissance to determine which ports are open on the network. Which of the following tasks should be done FIRST? (Choose two.)
A. Network scan
B. Banner grab
C. Tracert
D. DHCP server check
E. Brute-force attack
Correct Answer:
A. Network scan
C. Tracert
Exam Question 412
A technician is diagnosing an issue with a new T1 connection. The router is configured, the cable is connected, but the T1 is down. To verify the configuration of the router, which of the following tools should the technician use?
A. Loopback adapter
B. Cable tester
C. Tone generator
D. Multimeter
Correct Answer:
A. Loopback adapter
Exam Question 413
A network administrator configures an email server to use secure protocols. When the upgrade is completed, which of the following ports on the firewall should be configured to allow for connectivity? (Choose three.)
A. TCP 25
B. TCP 110
C. TCP 143
D. TCP 389
E. TCP 587
F. TCP 993
G. TCP 995
Correct Answer:
E. TCP 587
F. TCP 993
G. TCP 995
Exam Question 414
An ISP technician gets a call from a business that just changed equipment but can no longer connect to the Internet. The technician checks the ARP table on the ISP switch, and there is no corresponding MAC address present. Instead, the entry is “Incomplete”. Which of the following could cause this condition?
A. VLAN mismatch
B. Duplex/Speed mismatch
C. Duplicate IP address
D. TX/RX reverse
Correct Answer:
B. Duplex/Speed mismatch
Exam Question 415
Which of the following MUST be implemented to share metrics between routing protocols within the same router?
A. Routing loop
B. Routing table
C. Route redistribution
D. Dynamic routes
Correct Answer:
B. Routing table
Exam Question 416
A network security technician observes multiple attempts to scan network hosts and devices. All the attempts originate from a single host on the network. Which of the following threats is MOST likely involved?
A. Smurf attack
B. Rogue AP
C. Compromised system
D. Unintentional DoS
Correct Answer:
C. Compromised system
Exam Question 417
A user checks an IP address using an external website. The address is different than the one the user sees when opening a command prompt and typing in ipconfig/all. The user does not understand why the two tools show different IP addresses. This is BEST explained by the interworking of:
A. network devices
B. packet flow
C. public/private networks
D. traffic-routing protocols
Correct Answer:
C. public/private networks
Exam Question 418
A forensic first responder arrives at the scene where an employee is suspected to have committed a computer-based crime. Which of the following should the first responder do FIRST?
A. Document the scene
B. Take pictures upon arrival
C. Secure the area
D. Implement chain of custody
Correct Answer:
C. Secure the area
Exam Question 419
A user reports difficulties connecting a PC to a wired network. The PC connects to an IP phone, which is working correctly. A network technician can verify that other devices successfully connect to the phone. At which of the following layers of the OSI model is the problem MOST likely located?
A. Network
B. Physical
C. Transport
D. Application
Correct Answer:
A. Network
Exam Question 420
Multiple users are reporting that they are unable to access the network. The ENTIRE network is shown in the diagram. PCs are not statically assigned IP addresses. The following devices will display settings:
WorkstationA
WorkstationB
WorkstationC
WorkstationD
WorkstationE
WorkstationF
WorkstationG
Laptop1
Laptop2
DHCP server1
DHCP server2
Review the settings and select the box in the diagram that identifies the device causing the issue. Only one device can be selected at a time.
After checking the device that is causing the issue, select the second tab in the lower left hand corner.
Identify the reason as to why some users are unable to access the network.
Instructions: When the simulation is complete, select the Done button to submit.
Part 1
Workstation A
IP Address: 172.30.0.10
Netmask: 255.255.255.0
Gateway: 172.30.0.1
Workstation B
IP Address: 172.30.0.14
Netmask: 255.255.255.0
Gateway: 172.30.10.1
Workstation C
IP Address: 169.254.200.67
Netmask: 255.255.255.0
Gateway: –
Workstation D
IP Address: 172.16.0.21
Netmask: 255.255.255.0
Gateway: 172.16.0.1
Workstation E
IP Address: 172.16.0.21
Netmask: 255.255.255.0
Gateway: 172.16.0.1
Workstation F
IP Address: 172.16.10.43
Netmask: 255.255.255.0
Gateway: 172.16.10.1
Workstation G
IP Address: 172.16.10.120
Netmask: 255.255.255.0
Gateway: 172.16.10.1
Laptop 1
IP Address: 172.16.0.220
Netmask: 255.255.255.0
Gateway: 172.16.0.1
Laptop 2
IP Address: 172.30.0.12
Netmask: 255.255.255.0
Gateway: 172.30.0.1
DHCP server 1
IP Address: 172.30.0.5
Netmask: 255.255.255.0
Gateway: 172.30.0.1
DHCP Scope: 172.30.0.10-250
Gateway: 172.30.0.1
DNS Server: 10.200.2.20, 10.200.3.20
DHCP Lease Time: 8 Days
DHCP server 2
IP Address: 172.30.0.5
Netmask: 255.255.255.0
Gateway: 172.16.0.1
DHCP Scope: 172.16.0.10-250
Gateway: 172.16.0.1
DNS Server: 10.200.2.20, 10.200.3.20
DHCP Lease Time: 8 Days
Part 2
Identify the reason as to why some users are unable to access the network.
A. Workstation(s) are plugged into switch ports configured with half duplex.
B. The site-to-site router was configured with the incorrect ACL.
C. DHCP server scope is full and is not providing IP addresses.
D. WAN and LAN ports are reversed on the router.
E. STP has disabled some of the ports on the switch.
F. The NIC driver is not installed.
G. A wireless client is unable to associate to the AP.
Correct Answer:
G. A wireless client is unable to associate to the AP.